• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Ignition Cylinder Lock Repair (Http://Www.Mecosys.Com/Bbs/Board.Php?Bo_Table=Project_02&Wr_Id=1592754)

The ignition cylinder lock permits the key to be turned and the car to begin. It is controlled by a chamber that has springs which can be damaged by environmental conditions like low or high temperatures.

If your ignition switch or key doesn't move, it could indicate that the lock cylinder is damaged and must be replaced. This task should be left to an experienced auto locksmith.

Remove the steering column covers

Ignition lock-cylinders are mechanical components that allow a key inserted into the ignition switch to be turned to turn off the vehicle. They can fail or wear out in different ways, such as the key being placed too hard or not in the correct position. They may also fail due to corrosion or other causes. If your ignition cylinder isn't turning, it's probably time to replace it. You can do this yourself, but it's a job that requires removing the covers for the steering column and the airbag cover. The process is risky and challenging, and the replacement cylinder might require special tools to be installed.

The ignition cylinder is located in the middle of the column where the steering wheel is attached. The clip and two screws located at the bottom hold the cylinder in the right position. Take these screws off prior to working on the cylinder to stop it from slipping out and becoming lost.

After you have the screws removed, you can remove the plastic retainers out of the bottom of the cover. A metal retainer is inserted into the top of the cover to hold it in position. It is possible to pull off the cover to remove the tabs that are lower.

You can break them off by removing the screw that holds them and bending the tab outward. If the tab is broken completely you can replace it by using a piece of perforated strapping made of metal that is available at many hardware stores. You'll also require U-clips to secure the new bottom "tab," and these can be bought from any automotive parts store.

Once the plastic tabs are removed and the airbag cover has been removed, you are able to access the hole for the ignition cylinder. You can unlock the ignition lock using the 1/16-inch Allen wrench and pull the retaining bolt of the cylinder. Then, you'll be able to pull the cylinder out. You may need to replace it with a specific cylinder for an anti-theft system.

Remove the Ignition Cylinder

Although many newer vehicles have switched to push-to-start systems, there are still a good number of cars on the road that need an ignition lock cylinder. This mechanical cylinder is located inside the electrically powered component known as the ignition switch, which locks the ignition and "reads" anti-theft codes inside the car key so that it can start.

If your car is showing signs of a malfunctioning ignition lock cylinder, it may be time to contact an auto locksmith for assistance. A damaged cylinder can lead to several problems, including a absence of power from the engine, as well as issues with inserting and removing the key. Keys that are damaged by wear can cause damage to wafer tumblers, which let the ignition cylinder to turn. This leads to an obstruction and stops the vehicle from getting started.

Based on the model and the make, the ignition switch cover could be secured by clips or screws. With a screwdriver, loosen the screw, and then slide the cover off to reveal the ignition lock cylinder. It is typically a steel cylinder that is about the size of one quarter.

To remove the cylinder, you'll have to drill out the pin that holds it in place. Use a drill bit slightly larger than the slot for the key and then drill straight into it until the cylinder breaks free. Then, you can remove the cylinder and then replace it.

The procedure to remove the ignition cylinder varies by manufacturer, so you'll need to consult your service manual to determine what steps you need to take. After you have the cylinder removed, you are able to install the new ignition switch.

Before you can do this you'll have to replace the steering column covers. Also, you'll need to tighten two screws on the top of the lock assembly to hold it in place. Once you've done this, installing your new ignition cylinder should be relatively simple.

Remove the Ignition Switch

The ignition cylinder lock and switch are two distinct parts of your car ignition key replacement's electrical system. While they may seem identical, they can be replaced or repaired separately from one another. The switch is the electronic component that provides power to the vehicle while the cylinder is the mechanical tumbler your key is able to slide into. You can tell when the ignition cylinder has failed due to its inability to turn the key.

When the cylinder fails the pins in the tumbler can wear out, making it difficult or impossible to pull or insert your key. If you notice that your key has become worn and won't turn, your best bet is to get the wafers in it replaced or smoothed by a professional locksmith.

The ignition cylinder is exposed by removal of the bolt or screw, depending on the make of your vehicle. Check the manual of your vehicle before making the attempt at home. It is a risk and result in damage to the steering column or the plastic covers. Furthermore the switch is linked with airbags' wires, and tampering with this could result in serious injury.

To take the ignition cylinder out you'll need a drill to loosen it. It is also possible to use pliers, however, it is more difficult. If the ignition cylinder becomes loose and you need to replace it with a new one from a local auto locksmith ignition replacement store.

After installing the new ignition cylinder you'll need to connect all of the wires to the electrical connection inside the steering column and test it for proper function. It's generally easier to disconnect the battery, and then remove the ignition key and then start the car. It is possible to reconnect the battery after the ignition has worked. If it doesn't work, you'll need to reset the immobilizer system by a dealership or service technician. This is a complex procedure that should be left to a professional.

Reinstall the Ignition Cylinder

The ignition switch in your car transmits an alert to the car ignition lock's engine that it's time to get started. The key inserts into a lock cylinder to trigger this process, but the pins and wafers inside the cylinder could wear out over time. It may be difficult or impossible to start your vehicle if the cylinder becomes stuck.

If your car's key won't turn, it's likely that the ignition cylinder is worn down and needs replacing. A professional locksmith can replace the cylinder with an identical one, so your new key will function with the original ignition switch and will still be able to trigger the engine's startup signal.

To take out the old lock cylinder simply push it in to the release pin on the bottom of the assembly and slide the cylinder out from its housing. If the cylinder isn't sliding out, try pushing on the release pin again or using a screwdriver, you can press an anti-rotation small button underneath the cylinder's surface. You can also push down on the cylinder while turning the key to the ACC position, or attach an accessory to push it out.

Install the new cylinder and test it by turning on the vehicle. If it's not, you can reconnect any trim pieces you removed to access the cylinder and follow an anti-theft procedure to connect your new keys to the vehicle.

While the ignition cylinder lock isn't as crucial to the functioning of your car as it used to be, there are still many scenarios where you'll need to replace it. Consult a professional such as an locksmith or dealer in the automotive industry to ensure that the task is done without damaging the steering column plastic or other components of your vehicle. It's important to make sure that the new ignition is correctly coded to ensure that your car recognizes it as a genuine key. This usually requires an expert or a dealer to carry out this process of learning.