• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Turn the PCB/panel panel face down on VERY FLAT SURFACE. Place base PCB face down, with the pads to solder on the left side. The delivery air is going to require some new tooling but all I did was turn one of his same pieces up side down and used some tape to see how it would fit. Not only will you have better control over what they watch, but it also gives you a better opportunity to discuss what they see and explain things they may not understand. The serial port will provide the physical connection between the equipment but you need to use a communication protocol that has to be used to ensure a completely reliable, error-free data path. Uncomplicated to physically organize: One of the significant benefits of wireless Probe Monitoring is the capacity to transmit facility data without operating cable across spaces, throughout walls, floors, and ceilings. Will the bedroom be shared by both parents or will one use it exclusively? Connect this doorbell to the home Wi-Fi, and you will receive an instant notification after the bell rings. Now you can recreate the theater experience with no need to leave home!

So, when you get your hands on the ethernet cable, you don't need to worry about your internet speed. At this point, you'll need to trim a little bit off the top-left mount because it overlaps with the "SID R" LED. Test inserting a LED into the hole. LED by the leads and let it drop into the hole and hear the tapping sound when it hits the surface. The flat side of the LED should match the flat side of the symbol on the PCB. This means you should first cut lengths of 50mm and then strip 5mm of insulation of either end, and then bend the ends of the wires 90 degrees about 2mm from the insulation, towards the ribbed side. The best way to strip the insulation from the wires is to lightly score with a knife on the flat side, i.e. cut half-way through the insulation, not cutting to the wire, then do small cuts between each wire (from the score line to the end), then pull off each little bit of insulation with pliers, being careful not to grip the wire too much and pull the wire out.

Removing detents is really just squashing the little bump inside the encoder. This makes for a very strong connection with little stress on the solder joints or the exposed wire. If you are crazy and want to do illuminated knobs, NOW is the time to solder LEDs to the rotary encoders. Want more information on any of those plugs? At the same time, the camera electronics became more compact and the cameras successively smaller. The aim here is to make the LEDs poke out the same distance above the panel as the switch shafts. Note There is a potentially better method mentioned on the forums (here) which uses JST headers on the baseboard and either right-angled JST headers on the CS or just normal right-angled SIL headers. Coupled with ready-made JST cables, this is a much simpler approach and allows the two boards to be separated easily. This is a slightly difficult process, what is control cable so I'll give as much advice as possible. You must solder these on the top first then trim leads as close as possible. If the LED leads are really long, you can trim all the LED leads to 5mm above PCB, to make soldering easier. If any are not correct, you can heat up the joint and position the LED with pliers holding the lead, or a finger adjusting the unsoldered lead.

Turn it PCB side up, trim the leads to 1mm above PCB, and solder the second lead of each LED, and also do a proper solder joint on the first lead (if it wasn't done properly the first time). Also the shorter lead is the cathode. The cables should be connected so the cable sits flat against the top side of the CS PCB and the bottom side of the base PCB, so the solder joints are on the inside of the bent cable. Put the panel on top of the PCB, guiding it onto the PCB gently with the screws as a guide. Put the PCB in the PT-10 case top where the panel would normally go, so the LEDs can be put in without bending the leads. Mount the panel to the PT-10 case, using nuts to hold it on, then attach the PCB. Put the LEDs in the panel holes.