• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Cat flaps allow your pet to leave and come as they please, without you having to let them in or out. They also prevent your cat from urinating in the home.

It is easier to install a cat flap on a Upvc panel than on a glass one however, you'll need some skills and the right tools.

Measure the Door

Installing a cat door into a front door can be difficult however, provided that the cat flap is the correct one and you follow the guidelines it shouldn't be too difficult. We will show you how to mark out the shape, use a jigsaw to cut out the area in the back door with cat flap fitted and then finish the job by attaching the flap to the door. This will ensure the flap is in place and shields the doors from damage caused by rain and wind.

The first thing you need to do is take a measurement of the width of your pet in order to determine an accurate estimate of what size of cat flap you will require. This will ensure that the flap is big enough that your pet can enter and leave the house without needing to open and close the back door with cat flap fitted every time, but also small enough to stop the pet from straying too far in either direction.

If your kit has an illustration of the location to drill, you can stick it on the door and then draw a pencil around it. If your door has a moulding or sill on the bottom edge ensure that you have clearance from these as this will ensure your cat flap double glazing's safety and prevent them gaining access to your home.

Then put on your eye protection and a dust mask. Then using a jigsaw, begin cutting along the line you have pencilled in, don't try to push the blade too hard as this can make it cut faster than you'd like it to. Utilize a set square to ensure that you're cutting the material in a proper manner and that the hole is a rectangle shape. When you are happy with the result, you are able to remove the remaining door material.

Draw a Line

The cat flap lets you to let your pet go inside and out without having to worry about unwanted visitors or unwanted gifts. It also stops draughts and helps to keep your home's temperature in check. Installing a cat flap on your door might seem difficult to those who haven't tried it before. Many people call an expert joiner or carpenter to do the work. This is an option but you can do it yourself if your tools are right and the directions are followed.

While this is much easier to do with a wooden door, it is still possible in uPVC doors, but you need to be very cautious not to damage the doors as this will end your warranty. The first step is to measure the door, ensuring that it will be able to accommodate the new cat flap. If you have a standard uPVC panel it's easy. However in the case of composite or a different type of door, you might have to be more cautious.

The next step is to determine the height of your belly for your cat. This is the height between the floor and the bottom of your cat's stomach. You will need to locate an area on the door that will allow your pet to pass through comfortably. Once you know this then you need to mark out the area using an eraser and a spirit level so that you can be certain that the hole you will create will fit your cat.

After you have marked the area, it is time to cut the hole. It is essential to take your time and use a jigsaw in order to ensure that the cuts are smooth and clean not uneven and rough. This could cause damage to your door. You should also remember to wear safety glasses and a dust mask when using the jigsaw, as breathing in the dust could be harmful to your health. Once you've finished cutting the hole, you'll require sandpaper to smooth the edges so that the cat flap can be easily inserted into the hole.

Cut a Hole

It can be difficult to install a cat flap into a door panel or sealed double glazing unit. You may be tempted to tackle the job yourself, but unless have experience with DIY, it's recommended to hire a professional in to do the task for you. A botched job could not only look ugly but also pose an security risk. It could allow cold air in when the cat is outdoors and hot air out when inside.

The first thing to do is draw the location of the hole in the door using an eraser and an ax level. This will ensure that it is correctly located and is in a straight line with the other parts of the door. You should make sure you have a piece of sandpaper at ready to smooth any edges.

After the line is traced, you must cut the hole using a jigsaw. Be sure to wear any necessary safety gear for working with the power tool. If you're concerned about the noise, you can buy a jigsaw with a cord that is more quiet and easy to use.

You should only remove the material that is required to create the flap. It is essential to leave some extra material to cover the wall of the flap. However cutting off too much material can cause issues or even damage to the frame of the door.

A upvc door may contain a metal frame or panel within it that will interfere with the microchip cat flap in this case you will need to cut an oversize hole to ensure the metal doesn't touch the wall of the cat flap. If this is done it is important to fill in the oversize gap and render it watertight.

If you're planning to install a cat flap into a upvc or double-glazed window with metal frames, you'll need to consult a specialist. They can offer you a brand new piece of glass that has the hole already made for the cat flap. This will be cheaper than fitting a cat flap inside an existing pane of glass that was not designed specifically for this purpose.

Place the Flap

Cat flaps allow your pet the freedom to come and go whenever they want and let them relax in the house when they like. However, if you have a uPVC door, it may be difficult to fit a cat flap, particularly in the absence of glass panes that can be cut to accommodate one. If you're willing to purchase and install a half-glazed replacement uPVC panel, it's possible to add an animal flap onto the doors. It's not just a matter of drilling a hole into the door. It is also necessary to perform a few steps to ensure that the door is safe.

A composite, uPVC or GRP back door with cat flap fitted panel is usually comprised of a plastic skin that is bonded to an insulating polystyrene base. The material is quite fragile and care must be taken when cutting into it to avoid damaging. This type of door comes with a template that you can use to cut the hole.

After you've marked the location of the hole in your door, it's now time to put in the cat flap itself. You can choose from a wide range of models, ranging from simple push-button models to microchip activated ones that allow only your pet to enter. Whatever type of cat flaps you choose it's essential that your cat can use the flap comfortably without getting stuck in the rain.

It is a good idea to opt for a circular Fitting Cat flap In upvc door Panel rather than a square one, as circles can be more securely cut into door glass. This is because square holes can make glass more vulnerable to cracking if a drill is used on it. This is also a safer choice, as you won't have to drill into the toughened glass which could break and hurt your pet or your family members. This is particularly important if there are elderly or children living in your home that could be hurt by glass fragments.